102530 Lithium ion polymer Battery (LiPo) (3.7V 800mAh)

The batteries come pre-attached with a genuine 2-pin JST-PH connector, as shown; please check your current cable orientation, as there is no  Industry Standard for Cable setup. Wrong orientation can damage the cell and your Device.



50 in stock

Add to Wishlist
Dangerous Goods
102530 (3.7V 800mAh) Lithium-ion
This item: 102530 Lithium ion polymer Battery (LiPo) (3.7V 800mAh)

50 in stock

751643 Lithium ion polymer Battery lithium polymer
Mini MP1584en DC-DC 4.5 V to 28 V To 0.8 V to 20 V Step Down Module 3A Buck Converteradjustable-power-step-down-module-24v-to-12v-1.jpg
852040 Lithium ion polymer Battery lithium polymer
Qty Discount
2 - 4 5%
5 - 9 6.5%
10 + 8%
SKU: TS-B110
Additional information
Support & Utility
Q & A

102530 (3.7V 800mAh) Lithium-ion polymer Battery (LiPo). Each cell outputs a nominal 3.7V. These batteries have fast charge times, reliably hold a charge, and have built-in safety circuitry. These batteries are the best go-to option for any portable project.

Model series Info  102530 9.7 = Thickness, 25= Width, 31.2 = length + or -5%

Lithium-ion polymer (also known as ‘lipo’) batteries are thin, light, and powerful. When ultimately charged, they output from 4.2V to 3.7V. This battery has a capacity of 800mAh for a total of about 2.96Wh. If you need a larger (or smaller!) battery, we have an extensive range of Lithium-ion polymer batteries.

The protection circuitry keeps the battery voltage from going too high (over-charging) or having a low over-discharge, which means the battery will cut out when completely dead at 3.0V. It will also protect against output shorts. Even with this protection, it is essential that you only use a LiPo constant-voltage/current charger to recharge them at a rate of 0.5C or less.

Tempero Systems suggests charging at 0.5C or even less, which is 400mA max for this battery. Like most lipos, These batteries do not have thermistors built in.

The batteries come pre-attached with a 2-pin JST-PH connector and include the necessary protection circuitry. The JST-PH connector has 2.0mm spacing between its pins.

Note: This battery is NOT suitable for R.C. cars, planes, drones, or other devices that require high power(current); these need a high-rate battery with a continuous discharge rate of 5C, 10C, 15C, 20C, 25C, 30C, 40C, or 50C or higher.

Note Please check your current cable orientation, as there is no  Industry Standard for Cable setup. Wrong orientation can damage the cell and your item.

  • Model: 102530
  • Battery Chemical Composition: Lithium-Ion
  • Nominal Voltage: 3.7v
  • Nominal Capacity: 800mAh
  • Battery Watt Hour Rating (Required for Lithium Batteries): 2.96Wh
  • Max charge current: 1C
  • Cut-off Voltage: 2.75v +-5%
  • Standard Charging method: 0.5C CC (constant current) charge to 4.2V, then CV (constant voltage 4.2V) charge till charge current decline to ≤0.01C
  • Discharging method: Constant current 0.2 C end voltage 2.75V.
  • Charge Current: 0.2C = 160mA
  • Maximum Charge Current: 0.5C = 400mA
  • Max discharge current: 1C
  • Cut-off Voltage: 3.0V
  • C.V.: ≥3.85V
  • Connection Type: JST PH 2.0MM
  • Dimension: Thickness x Width x Height 3.9*24.2*30.7 mm
  • Weight: 14.1 Grams
  • Cycle Life: Over 500 times
  • Operating Environment: Charging: 0°C~45°C;65±20RH
  • Operating Environment: Discharging: 10°C~60°C;65±20RH
  • Storage temperature: -5℃~35℃
  • Charging Attention: Charging current and charging voltage should be less than specified.
  • Dangerous Road Freight: NO
  • Dangerous Air Freight: YES
Usage & Precaution:

Lithium-ion and lithium polymer cells are potent batteries; you should take extreme care when using them. If exposed to abusive conditions, they may get hot, explode, or ignite and cause serious injury. Unfortunately, we can not replace batteries damaged by non-compliant chargers or equipment.
Be sure to follow the safety warnings listed below:

Do not
  • overcharge: Ensure the charger voltage does not exceed the battery’s full charge voltage.
  • Over-discharge: Ensure the equipment you use with this battery will not draw more current from that battery than the stated “Maximum Continuous Discharge Current.”
  • leave batteries discharged for an extended period can incur irreversible damage
  • by placing the battery on fire, heating, or direct sunlight to the battery.
  • Install the battery backwards so the polarity is reversed.
  • Connect the battery’s positive and negative terminal with any metal object,
  • expose the battery to water or saltwater, or let the battery get wet.
  • Disassemble or modify the battery. The battery contains safety and protection devices.

Additional safety notes: Do not use a NiMH/NiCad/lead-acid charger! Also, never charge or use unattended. Always inspect batteries and surrounding circuitry constantly for damage, loose wiring, or the possibility of short circuits. As with all Lithium-ion polymer batteries and any power source, they should be used by experts who are comfortable working with power supplies.

Package Included: 102530 (3.7V 800mAh) Lithium-ion polymer Battery (LiPo)

Check out our On Sale and Clearance Items 

Development  Resources: Demo Codes, Schematics, Datasheets, Etc


Tempero systems Hackaday     Hackaday serves up Fresh Hacks Every Day from around the Internet.

tempero systems-InstructablesInstructables is a community for people who like to make things. Explore, share, and do your next project with us!

Tempero Systems-Github     Where the world builds software

tempero systems-Raspberry Pi    Raspberry Pi Foundation: What would you like to make today?

tempero systems-Arduino    Arduino‘s mission is to enable anyone to enhance their lives through accessible electronics and digital technologies.

tempero systems-Wikipedia     Wikipedia is a free online encyclopedia created and edited by volunteers worldwide and hosted by the Wikimedia Foundation.



1. There may be slight size deviations due to manual measurement and different measuring methods and tools.
2. The picture may not reflect the actual colour of the item because of different photography lights, angles and display monitors.


Weight 0.015 kg
Dimensions 3 × 2 × .5 cm

Product Applications

Q & A

There are no questions yet

Ask a question

Your question will be answered by a store representative or other customers.

Thank you for the question!

Your question has been received and will be answered soon. Please do not submit the same question again.



An error occurred when saving your question. Please report it to the website administrator. Additional information:

Add an answer

Thank you for the answer!

Your answer has been received and will be published soon. Please do not submit the same answer again.



An error occurred when saving your answer. Please report it to the website administrator. Additional information: