* All questions and comments are approved by a system administrator before re-posting to our FAQ product sections.
$13.95 (AUD)
The batteries come pre-attached with a 2-pin JST-PH connector, as shown; please check your current cable orientation, as there is no Industry Standard for Cable setup. Wrong orientation can damage the cell and your Device.
NOTICE: This item can only be shipped to Australian Addresses. Overseas Shipping not available.
Due to Australia Post Dangerous and prohibited goods Guidelines, These LiPo can only be sent Via Road.
Li-ion Battery Charger Protection Module 3S 10A
$4.95 (AUD) Add to Cart |
0 in stock | |||
Li-ion Battery Charger Protection Module 1S 2A
$3.25 (AUD) Add to Cart |
19 in stock | |||
Li-ion Battery 2S 3A Charger Protection Module
$3.95 (AUD) Add to Cart |
118 in stock |
Calculate Shipping - shipping options and estimates can be found in your shopping cart.
103048 (3.7V 1500mAh) Lithium-ion polymer Battery (LiPo). Each cell outputs a nominal 3.7V. These batteries have fast charge times, reliably hold a charge, and have built-in safety circuitry. These batteries are the best go-to option for any portable project.
Lithium-ion polymer lipo batteries are thin, light and powerful. The output ranges from 4.2V when ultimately charged to 3.7V. This battery has a capacity of 1500mAh for about 5.55Wh. We have an extensive range of lithium-ion polymer batteries if you need a larger or smaller battery.
Protection circuitry keeps the battery voltage from going too high (over-charging) or low over-discharge, which means the battery will cut out when completely dead at 3.0V. It will also protect against output shorts.
Even with this protection, it is essential that you only use a LiPo constant-voltage/current charger to recharge them at a rate of 0.5C or less. Tempero Systems suggests charging this battery at 0.5C or even less, 750mA max. Like most lipos, These batteries do not have thermistors built in.
The batteries come pre-attached with a 2-pin JST-PH connector and include the necessary protection circuitry. The JST-PH connector has 2.0mm spacing between its pins.
Note: NOT suitable for R.C. cars, planes, drones or other devices that require high power(current); these need a high-rate battery with a continuous discharge rate of 5C, 10C, 15C, 20C, 25C, 30C, 40C, 50C or higher.
Note: Please check your current cable orientation, as there is no Industry Standard for Cable setup. Wrong orientation can damage the cell and your item.
Lithium-ion and lithium polymer cells are potent batteries, and YOU should take extreme care. Using them may get hot, explode or ignite and cause serious injury if exposed to abusive conditions. Unfortunately, we can not replace batteries damaged by non-compliant chargers or equipment.
Be sure to follow the safety warnings listed below:
Additional safety notes: Do not use a NiMH/NiCad/lead-acid charger! Also, Never charge or use unattended. Always inspect batteries and surrounding circuitry constantly for any damage, loose wiring, or the possibility of short circuits. As with all Lithium-ion polymer batteries and any power source – they should be used by experts who are comfortable working with power supplies.
Package included: 103048 (3.7V 1500mAh) Lithium-ion polymer Battery (LiPo)
Check out our On Sale and Clearance Items
Hackaday serves up Fresh Hacks Every Day from around the Internet.
Instructables is a community for people who like to make things. Explore, share, and do your next project with us!
Where the world builds software
Raspberry Pi Foundation: What would you like to make today?
Arduino’s mission is to enable anyone to enhance their lives through accessible electronics and digital technologies.
Wikipedia is a free online encyclopedia created and edited by volunteers worldwide and hosted by the Wikimedia Foundation.
Notes:
1. There may be slight size deviations due to manual measurement and different measuring methods and tools.
2. The picture may not reflect the actual colour of the item because of different photography lights, angles and display monitors.
Weight | 0.032 kg |
---|---|
Dimensions | 4.5 × 2 × 1 cm |
Tempero Systems offers many custom IoT electronic design services to help tailor our product to your exact needs. Whether you are looking for custom firmware, circuit board modifications, metal enclosures, or industrial color printing, we can help you with a wide variety of design services.
Please login or register to ask a question. Thanks
* All questions and comments are approved by a system administrator before re-posting to our FAQ product sections.