502030 (3.7V 250mAh) Lithium ion polymer Battery (LiPo)
The batteries come pre-attached with a genuine 2-pin JST-PH connector, as shown; please check your current cable orientation, as there is no Industry Standard for Cable setup. Wrong orientation can damage the cell and your item.
Out of stock
502030 (3.7V 250mAh) Lithium-ion polymer Battery (LiPo). Each cell outputs a nominal 3.7V. These batteries have fast charge times, reliably hold a charge, and have built-in safety circuitry. These batteries are the best go-to option for any portable project.
Model series Info 502030 4.83 = Thickness, 19.6= Width, 30 = length + or -5%
Lithium-ion polymer (also known as ‘lipo’) batteries are thin, light and powerful. The output ranges from 4.2V when ultimately charged to 3.7V. This battery has a capacity of xxxxmAh for a total of about 0.925Wh. If you need a larger (or smaller!) battery, we have an extensive range of Lithium-ion polymer batteries.
Protection circuitry keeps the battery voltage from going too high (over-charging) or low over-discharge, which means the battery will cut out when completely dead at 3.0V. It will also protect against output shorts.
Even with this protection, it is essential that you only use a LiPo constant-voltage/current charger to recharge them at a rate of 0.5C or less. Tempero Systems suggests charging this battery at 0.5C or even less, 125mA max. Like most lipos, These batteries do not have thermistors built in.
The batteries come pre-attached with a 2-pin JST-PH connector and include the necessary protection circuitry. The JST-PH connector has 2.0mm spacing between its pins.
Note: NOT suitable for R.C. cars, planes, drones or other devices that require high power(current); these need a high-rate battery with a continuous discharge rate of 5C, 10C, 15C, 20C, 25C, 30C, 40C, 50C or higher.
Note: Please check your current cable orientation, as there is no Industry Standard for Cable setup. Wrong orientation can damage the cell and your item.
Specifications:
- Model: 502030
- Battery Chemical Composition: Lithium-Ion
- Nominal Voltage: 3.7v
- Nominal Capacity: 250 mAh
- Battery Watt Hour Rating (Required for Lithium Batteries): 0.925 Wh
- Max charge current: 1C
- Cut-off Voltage: 2.75v +-5%
- Standard Charging method: 0.5C CC (constant current) charge to 4.2V, then CV (constant voltage 4.2V) charge till charge current decline to ≤0.01C
- Discharging method: Constant current 0.2 C end voltage 2.75V.
- Charge Current: 0.2C = 50 mA
- Maximum Charge Current: 0.5C = 125mA
- Max discharge current: 1C
- Cut-off Voltage: 3.0V
- C.V.: ≥3.85V
- Connection Type: JST PH 2.0MM
- Dimension: Thickness x Width x Height 4.83*19.6*30 mm
- Weight: 5.7 Grams
- Cycle Life: Over 500 times
- Operating Environment: Charging: 0°C~45°C;65±20RH
- Operating Environment: Discharging: 10°C~60°C;65±20RH
- Storage temperature: -5℃~35℃
- Charging Attention: Charging current and charging voltage should be less than specified.
- Dangerous Road Freight: NO
- Dangerous Air Freight: YES
Usage & Precaution:
Lithium-ion and lithium polymer cells are potent batteries, and YOU should take extreme care. Using them may get hot, explode or ignite and cause serious injury if exposed to abusive conditions. Unfortunately, we can not replace batteries damaged by non-compliant chargers or equipment.
Be sure to follow the safety warnings listed below:
Do not
- overcharge: Ensure the charger voltage does not exceed the battery’s full charge voltage.
- Over-discharge: Ensure the equipment you use with this battery will not draw more current from that battery than the stated “Maximum Continuous Discharge Current.”
- leave batteries discharged for an extended period can incur irreversible damage
- by placing the battery on fire, heating, or direct sunlight to the battery.
- Install the battery backwards so the polarity is reversed.
- Connect the battery’s positive and negative terminal with any metal object,
- expose the battery to water or saltwater, or let the battery get wet.
- Disassemble or modify the battery. The battery contains safety and protection devices.
Additional safety notes: Do not use a NiMH/NiCad/lead-acid charger! Also, Never charge or use unattended. Always inspect batteries and surrounding circuitry constantly for any damage, loose wiring, or the possibility of short circuits. As with all Lithium-ion polymer batteries and any power source – they should be used by experts who are comfortable working with power supplies.
Package included: 502030 (3.7V 250mAh) Lithium-ion polymer Battery (LiPo)
Check out our On Sale and Clearance Items
Development Resources: demo codes, schematics, datasheets, etc
Hackaday serves up Fresh Hacks Every Day from around the Internet.
Instructables is a community for people who like to make things. Explore, share, and do your next project with us!
Where the world builds software
Raspberry Pi Foundation: What would you like to make today?
Arduino’s mission is to enable anyone to enhance their lives through accessible electronics and digital technologies.
Wikipedia is a free online encyclopedia created and edited by volunteers worldwide and hosted by the Wikimedia Foundation.
Notes:
1. There may be slight size deviations due to manual measurement and different measuring methods and tools.
2. The picture may not reflect the actual colour of the item because of different photography lights, angles and display monitors.
Weight | 0.010 kg |
---|---|
Dimensions | 6 × 3 × .8 cm |