.  . 2-pin Lithium-ion polymer, 550mAh, Lithium Ion Polymer, Power Control . 503040 Lithium ion polymer Battery (LiPo) (3.7V 550mAh)

503040 Lithium ion polymer Battery (LiPo) (3.7V 550mAh)

$11.25 (AUD)

The batteries come pre-attached with a 2-pin JST-PH connector, as shown; please check your current cable orientation, as there is no  Industry Standard for Cable setup. Wrong orientation can damage the cell and your Device.

NOTICE: This item can only be shipped to Australian Addresses. Overseas Shipping not available.
Due to Australia Post Dangerous and prohibited goods Guidelines, These LiPo can only be sent Via Road.

43 in stock

Qty Discount
2 - 4 5%
5 - 9 8%
10 + 10%
SKU: TS-B012 Categories: , , , Brand:

Recommended and Related Products.

Lipo Safe Bag 180 x 230 mm
$6.65 (AUD) Add to Cart
11 in stock
1S 5 Way Parallel Balance Charging Board
$12.95 (AUD) Add to Cart
10 in stock
HTRC T240 DUO Charger
$169.95 (AUD) Add to Cart
2 in stock
Li-po Battery Protection Bag 300 x 230 mm
$6.99 (AUD) Add to Cart
0 in stock


We Ship World Wide We are an Australian owned and Based Company. We are an Australian owned and Based Company. We are an Australian owned and Based Company. We are an Australian owned and Based Company. We are an Australian owned and Based Company. We are an Australian owned and Based Company. We are an Australian owned and Based Company.

Calculate Shipping - shipping options and estimates can be found in your shopping cart.

503040  Lithium ion polymer Battery LiPo 3.7V 550mAh Each cell outputs a nominal 3.7V. These batteries have fast charge times, reliably hold a charge, and have built-in safety circuitry. These batteries are the best go-to option for any portable project.

Model series Info 503040 4.8 = Thickness, 29.7 = Width, 41.2 = length + or -5%

Lithium-ion polymer (lipo) batteries are thin, light and powerful. The output ranges from 4.2V when ultimately charged to 3.7V. This battery has a capacity of 550mAh for a total of about 2.035Wh. If you need a larger (or smaller!) battery, we have an extensive range of Lithium-ion polymer batteries.

Protection circuitry keeps the battery voltage from going too high (over-charging) or low over-discharge, which means the battery will cut out when completely dead at 3.0V. It will also protect against output shorts. Even with this protection, it is essential that you only use a LiPo constant-voltage/current charger to recharge them at a rate of 0.5C or less.

Tempero Systems suggests charging at 0.5C or even less, which is 275mA max for this battery. Like most lipos, These batteries do not have thermistors built in.

The batteries come pre-attached with a 2-pin JST-PH connector and include the necessary protection circuitry. The JST-PH connector has 2.0mm spacing between its pins.

Check the polarity of the connector(polarized type) matches the polarity of your equipment! There is no standard for LiPo batteries’ polarity with a JST-PH connector. We used the polarity that seems to be most common, but your equipment can be different! If it does not match, it is easy to change the connector polarity.

Use a thin blade Screw Driver or similar to press down on the small latch securing each crimp socket in the housing and swap them. Ensure they do NOT touch each other.

The batteries come pre-attached with a 2-pin JST-PH connector and include the necessary protection circuitry. The JST-PH connector has 2.0mm spacing between its pins.

Note:  NOT suitable for R.C. cars, planes, drones or other devices that require high power(current); these need a high-rate battery with a continuous discharge rate of 5C, 10C, 15C, 20C, 25C, 30C, 40C, 50C or higher.

Note Please check your current cable orientation, as there is no  Industry Standard for Cable setup. Wrong orientation can damage the cell and your item.

Specifications:
  • Model: 503040
  • Battery Chemical Composition: Lithium-Ion
  • Nominal Voltage: 3.7v
  • Nominal Capacity: 550mAh
  • Battery Watt Hour Rating (Required for Lithium Batteries): 2.035Wh
  • Max charge current: 1C
  • Cut-off Voltage: 2.75v +-5%
  • Standard Charging method: 0.5C CC (constant current) charge to 4.2V, then CV (constant voltage 4.2V) charge till charge current decline to ≤0.01C
  • Discharging method: Constant current 0.2 C end voltage 2.75V.
  • Charge Current: 0.2C = 110mA
  • Maximum Charge Current: 0.5C = 275mA
  • Max discharge current: 1C
  • Cut-off Voltage: 3.0V
  • C.V.: ≥3.85V
  • Connection Type: JST PH 2.0MM
  • Dimension:  Thickness x Width x Height 4.8*29.7*41.3 mm
  • Weight: 12.3 Grams
  • Cycle Life: Over 500 times
  • Operating Environment: Charging: 0°C~45°C;65±20RH
  • Operating Environment: Discharging: 10°C~60°C;65±20RH
  • Storage temperature: -5℃~35℃
  • Charging Attention: Charging current and charging voltage should be less than specified.
  • Dangerous Road Freight: NO
  • Dangerous Air Freight: YES
Usage & Precaution:

Lithium-ion and lithium polymer cells are powerful batteries, and YOU should take extreme care. Using them may get hot, explode or ignite and cause serious injury if exposed to abusive conditions. Unfortunately, we can not replace batteries damaged by non-compliant chargers or equipment.
Be sure to follow the safety warnings listed below:

Do not
  • Overcharge: Ensure the charger voltage does not exceed the battery’s full charge voltage.
  • Over-discharge: Ensure the equipment you use this battery will not draw more current from that battery than the stated Maximum Continuous Discharge Current.
  • Leave batteries discharged for an extended period can incur irreversible damage
  • by placing the battery on fire, heating, or direct sunlight to the battery.
  • Install the battery backwards so the polarity is reversed.
  • Connect the battery’s positive and negative terminal with any metal object,
  • expose the battery to water or saltwater, or let the battery get wet.
  • Disassemble or modify the battery. The battery contains safety and protection devices.

Additional safety notes: Do not use a NiMH/NiCad/lead-acid charger! Also, Never charge or use unattended. Always inspect batteries and surrounding circuitry constantly for any damage, loose wiring, or the possibility of short circuits. As with all Lithium-ion polymer batteries and any power source – they should be used by experts who are comfortable working with power supplies.

Package Included: 1x 503040 Lithium ion polymer Battery LiPo 3.7V 550mAh

Check out our On Sale and Clearance Items 

Development  Resources: Demo Codes, Schematics, Datasheets, Etc

 

Tempero systems Hackaday     Hackaday serves up Fresh Hacks Every Day from around the Internet.

tempero systems-InstructablesInstructables is a community for people who like to make things. Explore, share, and do your next project with us!

Tempero Systems-Github     Where the world builds software

tempero systems-Raspberry Pi    Raspberry Pi Foundation: What would you like to make today?

tempero systems-Arduino    Arduino‘s mission is to enable anyone to enhance their lives through accessible electronics and digital technologies.

tempero systems-Wikipedia     Wikipedia is a free online encyclopedia created and edited by volunteers worldwide and hosted by the Wikimedia Foundation.

 

Notes:

1. There may be slight size deviations due to manual measurement and different measuring methods and tools.
2. The picture may not reflect the actual colour of the item because of different photography lights, angles and display monitors.

Weight 0.015 kg
Dimensions 4.5 × 2 × .7 cm

Product Applications



Current Product Support

SKU Product Type Download/View
TS-B012 503040 Lithium ion polymer Battery (LiPo) (3.7V 550mAh) - BATTERY PROTECTION IC FOR 1-CELL PACK Datasheet Download
TS-B012 503040 Lithium ion polymer Battery (LiPo) (3.7V 550mAh) - Battery Protection circuit Datasheet Download

We Customize Just for You!!

Tempero Systems offers many custom IoT electronic design services to help tailor our product to your exact needs. Whether you are looking for custom firmware, circuit board modifications, metal enclosures, or industrial color printing, we can help you with a wide variety of design services.


Our senior engineers provide you correct power solution and design for applications according to your products. Our customers are from all over the world. We welcome your contact.

Product Reviews and FAQ's

Please login or register to ask a question. Thanks

Post Your Question

×

* All questions and comments are approved by a system administrator before re-posting to our FAQ product sections.