* All questions and comments are approved by a system administrator before re-posting to our FAQ product sections.
0
- No products in the cart.
LiPo Battery 682030 (3.7V 250mAh) High Discharge Polymer Lithium Ion
$8.95 (AUD)
The batteries come pre-attached with a Molex 51005 Connector with a 10cm cable, as shown, and include the necessary protection circuitry. Quadcopter Syma X11C
NOTICE: This item can only be shipped to Australian Addresses. Overseas Shipping not available.
Due to Australia Post Dangerous and prohibited goods Guidelines, These LiPo can only be sent Via Road.
|
ISDT Q6 Nano 200W 8A 1-6s
$65.00 (AUD) Add to Cart |
2 in stock | ||
|
HTRC T240 DUO Charger
$169.95 (AUD) Add to Cart |
2 in stock | ||
|
Li-po Battery Protection Bag 300 x 230 mm
$6.99 (AUD) Add to Cart |
4 in stock |
Calculate Shipping - shipping options and estimates can be found in your shopping cart.
LiPo Battery 682030 (3.7V 250mAh) High Discharge Polymer Lithium Ion These Cells are Designed with 25C discharge. This makes them appropriate for R.C. cars, planes, drones, helicopters, quadcopters, etc.
High Discharge Battery is designed to supply a continuous discharge rate of 25C over a brief time; this is why they are great for R.C. cars, planes, and drones, whereas normal Lipo supplies current over days to months at 1C or less.
Model series Info 682030 8.5 = Thickness, 20 = Width, 31 = length + or -3%
Lithium-ion polymer (also known as ‘lipo’) batteries are thin, light and powerful. The output ranges from 4.2V when ultimately charged to 3.7V. This battery has a capacity of 250mAh for a total of about 0.925Wh. If you need a larger (or smaller!) battery, we have an extensive range of Lithium-ion polymer batteries.
Protection circuitry keeps the battery voltage from going too high (over-charging) or low over-discharge, which means the battery will cut out when completely dead at 2.75V. It will also protect against output shorts. Even with this protection, it is essential that you only use a LiPo constant-voltage/current charger to recharge them at a rate of 0.5C or 1C.
Tempero Systems suggests charging at 0.5C or even less for a longer Life.
High Discharge Battery comes pre-attached with a Molex 51005 2-pin connector with 2.0mm spacing and includes the necessary protection circuitry.
Note: Please check your current cable orientation, as there is no Industry Standard for Cable setup. Wrong orientation can damage the cell and your item.
If it does not match, it is easy to alternate the connector orientation. Just use a Plastic Pry Tool or similar to press down on the small latch securing each crimp socket in the housing and swap them. Ensure they do NOT touch each other!
Specifications: LiPo Battery 682030 (3.7V 250mAh)
- Model: 682030
- Battery Chemical Composition: Lithium-Ion
- Nominal Voltage: 3.7v
- Nominal Capacity: 250 mAh
- Battery Watt Hour Rating (Required for Lithium Batteries): 0.925 Wh
- High Discharge rate: 25C
- Cut-off Voltage: 2.75v +-5%
- Standard Charging method: 0.5C CC (constant current) charge to 4.2V, then CV (constant voltage 4.2V) charge till charge current decline to ≤0.01C
- Discharging method: Constant current 0.2 C end voltage 2.75V.
- Maximum Charge Current: 0.5C to 0.8C (0.5C) is recommended for longer Life
- Charging time: 0.5 Hours @ 0.5C
- C.V.: ≥3.85V
- Connection Type: Molex 51005
- Cable: 10cm
- Dimension: Thickness x Width x Height 8.5*20*31 mm
- Weight: 8 Grams
- Cycle Life: Over 500 times
- Operating Environment: Charging: 0°C~45°C;65±20RH
- Operating Environment: Discharging: 10°C~60°C;65±20RH
- Storage temperature: -5℃~35℃
- Charging Attention: Charging current and charging voltage should be less than specified.
- Dangerous Road Freight: NO
- Dangerous Air Freight: YES
Specifications: Molex 51005-0200
- Maximum current per contact is 2A
- Pitch – Mating Interface 2.00mm
- Natural colour
- Temperature Range – Operating -40° to +105°C
- UL94V-0 Flammability rating
The approximate charging time
- When the charging current is less than 5% of the battery capacity: charging time(H)= Battery capacity(MAH)×1.6÷Charging current(M.A.)
- When the charging current is more significant than 5% but less than 10% of the battery capacity: charging time(H)= Battery capacity(MAH)×1.5÷Charging current(M.A.)
- When the charging current is more significant than 10% but less than 15% of the battery capacity: charging time(H)= Battery capacity(MAH)×1.3÷Charging current(M.A.)
- When the charging current is more significant than 15% but less than 20% of the battery capacity: charging time(H)= Battery capacity(MAH)×1.2÷Charging current(M.A.)
- When the charging current is more significant than 20% of the battery capacity: charging time(H)= Battery capacity(MAH)×1.1÷Charging current(M.A.)
Usage & Precaution:
Lithium-ion and lithium polymer cells are effective batteries, and YOU must take extreme care. Using them may get hot, explode or ignite and cause serious injury if exposed to abusive conditions. Unfortunately, we can not replace batteries damaged by non-compliant chargers or equipment.
Be sure to follow the safety warnings listed below:
Do not
- Overcharge: Ensure the charger voltage does not exceed the battery’s full charge voltage.
- Over-discharge: Ensure the equipment you use this battery will not draw more current from that battery than the stated “Maximum Continuous Discharge Current.”
- leave batteries discharged for an extended period can incur irreversible damage
- by placing the battery on fire, heating, or direct sunlight to the battery.
- Install the battery backwards so the polarity is reversed.
- Connect the battery’s positive and negative terminal with any metal object,
- expose the battery to water or saltwater, or let the battery get wet.
- Disassemble or modify the battery. The battery contains safety and protection devices.
Additional safety notes: Do not use a NiMH/NiCad/lead-acid charger! Also, Never charge or use unattended. Always inspect batteries and surrounding circuitry constantly for any damage, loose wiring, or the possibility of short circuits. As with all Lithium-ion polymer batteries and any power source – they should be used by experts who are comfortable working with power supplies.
Package included: LiPo Battery 682030 (3.7V 250mAh) High Discharge Polymer Lithium Ion.
Check out our On Sale and Clearance Items
Development Resources: Demo codes, Schematics, Datasheets, etc
Hackaday serves up Fresh Hacks Every Day from around the Internet.
Instructables is a community for people who like to make things. Explore, share, and do your next project with us!
Where the world builds software
Raspberry Pi Foundation: What would you like to make today?
Arduino’s mission is to enable anyone to enhance their lives through accessible electronics and digital technologies.
Wikipedia is a free online encyclopedia created and edited by volunteers worldwide and hosted by the Wikimedia Foundation.
Notes:
1. There may be slight size deviations due to manual measurement, different measuring methods and tools.
2. The picture may not reflect the actual colour of the item because of different photography lights, angles and display monitors.
| Weight | 0.010 kg |
|---|---|
| Dimensions | 4 × 3 × 1.1 cm |
Product Applications
Battery for Quadcopter Syma X11C
We Customize Just for You!!
Tempero Systems offers many custom IoT electronic design services to help tailor our product to your exact needs. Whether you are looking for custom firmware, circuit board modifications, metal enclosures, or industrial color printing, we can help you with a wide variety of design services.
Our senior engineers provide you correct power solution and design for applications according to your products. Our customers are from all over the world. We welcome your contact.
Product Reviews and FAQ's
Please login or register to ask a question. Thanks
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.