1.44 inch TFT LCD module Colorful 128 x 128 ST7735 Driver IC Red Serial SPI without Touch
Clear display Using the SPI serial bus, it only takes a few IOs to illuminate the display. Easy to expand the experiment with SD card slot
Military-grade process standards, long-term stable work.
2 in stock
2 in stock
Dupont Jumper Wires Solderless 65, 75 and 130 piece pack
$4.25 – $8.50 (AUD) Options |
1.44 inch TFT LCD module uses; ST7735; drive chip to drive 128×128 dot, with 128 x 128; resolution; 1.44-inch screen with SPI serial module, a minimum of only four IO-driven resolution 128 * 128 Perfect upgrade actual colour, replace the black and white LCD screen for; Nokia 5110/3310 This TFT LCD Display Module; comes With PCB plate
Feature:
- LCD Type: 1.44 inch TFT LCD module Colourful Screen 128 x 128 Screen ST7735 Driver IC Red Serial SPI without Touch
- Display Type: Active Matrix TFT-LCD
- Dimensional Outline: 32.36 x 38 x 2.6 mm
- Number of Pixels: 128 x 128
- Active Area: 25.5 x 26.5mm
- Pixel Pitch: 0.1992 x 0.2070
- Resolution: 128(RGB) x128
- Display Mode: Transmissive type
- Display Color: 262K colors
- Drive IC: ST7735S
- Contrast Ratio: 400:1
- Interface: 4-wire SPI interface
- Backlight: 1 white LED, 18mA, 3.15V (Typ.)
- Luminance: 120 cd/m2 (Typ.)
Note: Power is 2.8-3.3V; remember not to use 5V (with PCB module has inherited the 3V regulator IC, you can enter 5V)
Data port level: In theory, the data port level should not exceed 3.3V Backlight Power (LED Pins):
3.2V Maximum Backlight Power (3.3V Supply Can be Series Connected for 10 Ohm Current Limiting Resistor in Series with 100 Ohm or 5V Resistors)
Storage.
- Do not expose the LCD modules to sunlight directly.
- The liquid crystal is deteriorated by ultraviolet. Please do not leave it in an intense ultraviolet ray for long.
- Avoid condensation of water. It may cause improper operation.
- Please stack only up to the number stated on the carton box for storage and transportation. Excessive weight will cause deformation and damage to the carton box.
Operation.
- When mounting or dismounting the LCD modules, turn the power off.
- Protect the LCD modules from electric shock.
- The Driver IC control algorithms stated above should always obey to avoid damaging the LSI and electronic circuit.
- Be careful to avoid mixing up the polarity of the power supply for the backlight.
- (When a static image is displayed for a long time, a remnant image is likely to occur.
- Most touch screens have air vents to equalize the inside air pressure to the outside. The air vent must be open, and you must avoid liquid contact as the liquid may be absorbed if liquid is accumulated near the air vent. Be sure to avoid bending the FPC to an acute shape; it might break FPC.
- For the fragility of ITO film, it should avoid tapering the pen as the input material.
Package included: 1 x 1.44 inch TFT LCD module Colorful 128 x 128
Check out our On Sale and Clearance Items
Development Resources: demo codes, schematics, datasheets, etc
Youtube: Arduino Tutorial: Using the 1.44″ Color TFT display (ILI9163C) with Arduino
Hackaday serves up Fresh Hacks Every Day from around the Internet.
Instructables is a community for people who like to make things. Explore, share, and do your next project with us!
Where the world builds software
Raspberry Pi Foundation What would you like to make today?
Arduino‘s mission is to enable anyone to enhance their lives through accessible electronics and digital technologies.
Wikipedia is a free online encyclopedia created and edited by volunteers worldwide and hosted by the Wikimedia Foundation.
Notes:
1. There may be slight size deviations due to manual measurement, different measuring methods and tools.
2. The picture may not reflect the actual colour of the item because of different photographing light, angles and display monitors.
Weight | 0.065 kg |
---|---|
Dimensions | 7.5 × 5.2 × 1 cm |