906090 Lithium ion polymer Battery (LiPo) (3.7V 6000mAh)
The batteries come pre-attached with a 2-pin JST-PH connector, as shown; please check your current cable orientation, as there is no Industry Standard for Cable setup. Wrong orientation can damage the cell and your Device.
38 in stock
38 in stock
906090 Lithium-ion polymer battery (LiPo) (3.7V 6000mAh) 2 pin. Each cell outputs a nominal 3.7V. These batteries have fast charge times, can reliably hold a charge, and have built-in safety circuitry. They are compatible with the PiJuice. The PiJuice Zero HAT doesn’t come with a standard onboard battery.
Model series Info 906090 9.0= Thickness 60.5 = Width, 90.5 = length + or -5%
Lithium-ion polymer (also known as ‘lipo’) batteries are thin, light, and powerful. When ultimately charged, they output 4.2V to 3.7V. This battery has a capacity of 6000mAh, for a total of about 22.2Wh. If you need a larger (or smaller!) battery, we have an extensive range of Lithium-ion polymer batteries.
The protection circuitry keeps the battery voltage from going too high (over-charging) or having a low over-discharge, which means the battery will cut out when completely dead at 3.0V. It will also protect against output shorts.
Even with this protection, it is essential that you only use a LiPo constant-voltage/current charger to recharge them at 0.5C or less. Tempero Systems suggests charging this battery at 0.5C or even less, 1500mA max. Like most lipos, These batteries do not have thermistors built in.
The batteries come pre-attached with a 2-pin JST-PH connector and include the necessary protection circuitry. The JST-PH connector has 2.0mm spacing between its pins.
Note: This is a generic LiPo battery compatible with PiJuice using a custom profile in the PiJuice configuration software. The standard PiJuice battery profiles may not work as intended with this battery
Specifications:
- Model: 906090
- Battery Chemical Composition: Lithium-Ion
- Nominal Voltage: 3.7v
- Nominal Capacity: 6000mAh
- Battery Watt Hour Rating (Required for Lithium Batteries):22.2Wh
- Max charge current: 1C
- Cut-off Voltage: 2.75v +-5%
- Standard Charging method: 0.5C CC (constant current) charge to 4.2V, then CV (constant voltage 4.2V) charge till charge current decline to ≤0.01C
- Discharging method: Constant current 0.2 C end voltage 2.75V.
- Charge Current: 0.2C = 1200mA
- Maximum Charge Current: 0.5C = 3000mA
- Max discharge current: 1C
- Cut-off Voltage: 3.0V
- C.V: ≥3.85V
- Connection Type: 2-pin JST PH 2.0MM
- Onboard NTC Temperature Sensor
- Dimension: Thickness x Width x Height 9×60.5×90.5 mm
- Weight: 106.1 Grams
- Cycle Life: Over 500 times
- Operating Environment: Charging: 0°C~45°C;65±20RH
- Operating Environment: Discharging: 10°C~60°C;65±20RH
- Storage temperature: -5℃~35℃
- Charging Attention: Charging current and charging voltage should be less than specified.
- Dangerous Road Freight: NO
- Dangerous Air Freight: YES
Usage & Precaution:
Lithium-ion and lithium polymer cells are very powerful batteries, and you should take extreme care when using them. If exposed to abusive conditions, they may get hot, explode, or ignite and cause serious injury. Unfortunately, we can not replace batteries damaged by non-compliant chargers or equipment.
Be sure to follow the safety warnings listed below:
Do not
- overcharge: Ensure the charger voltage does not exceed the battery’s stated full charge voltage.
- Over-discharge: Ensure the equipment you use this battery will not draw more current from that battery than the stated “Maximum Continuous Discharge Current.”
- Leaving batteries discharged for an extended period can incur irreversible damage.
- Place the battery on fire, heating, or direct sunlight to the battery.
- Install the battery backwards so the polarity is reversed.
- Connect the battery’s positive and negative terminal with any metal object,
- Expose the battery to water or saltwater, or let the battery get wet.
- Disassemble or modify the battery. The battery contains safety and protection devices.
Additional safety notes: Do not use a NiMH/NiCad/lead-acid charger! Also, Never charge or use unattended. Always inspect batteries and surrounding circuitry constantly for any damage, loose wiring, or the possibility of short circuits. As with all Lithium-ion polymer batteries and any power source – they should be used by experts who are comfortable working with power supplies.
Package included: 1x 906090 Lithium ion polymer Battery (LiPo) (3.7V 6000mAh) 2 pin.
Check out our On Sale and Clearance Items
Development Resources: demo codes, schematics, datasheets, etc
Hackaday serves up Fresh Hacks Every Day from around the Internet.
Instructables is a community for people who like to make things. Explore, share, and do your next project with us!
Where the world builds software
Raspberry Pi Foundation What would you like to make today?
Arduino’s mission is to enable anyone to enhance their lives through accessible electronics and digital technologies.
Wikipedia is a free online encyclopedia created and edited by volunteers worldwide and hosted by the Wikimedia Foundation.
Notes:
1. There may be slight size deviations due to manual measurement, different measuring methods and tools.
2. The picture may not reflect the actual colour of the item because of different photographing lights, angles and display monitors.
Weight | 0.115 kg |
---|---|
Dimensions | 16 × 9 × 1 cm |