0.96 Inch LCD Blue White Yellow-Blue SPI / IIC OLED Module 7pin

Provides a rich sample program for STM32, C51, Arduino, Raspberry Pi and MSP430 platforms the OLED display, no need backlight, self-illumination, the display performance is better than the traditional LCD display, also lower consumption.

$8.95
Colour Text
resetClear
Add to Wishlist
0.96 Inch Blue,White,Yellow-Blue SPI / IIC OLED LCD Module 7pin
This item: 0.96 Inch LCD Blue White Yellow-Blue SPI / IIC OLED Module 7pin
$8.95
$8.95
1.8 inch TFT LCD Module LCD Screen SPI Serial 51 Resolution 128 x 160
$12.95
Nextion NX4024T032 3.2 inch
1 × Nextion NX4024T032 3.2 inch

Out of stock

$55.95
$27.95
Qty Discount
2 - 4 5%
5 - 9 6.5%
10 + 8%
SKU: N/A
Description
Additional information
Applications
Support & Utility
Q & A

0.96 Inch LCD Blue White Yellow-Blue SPI / IIC OLED Module 7pin, no need for a backlight, self-illumination, the display performance is better than the traditional LCD, and it has lower consumption.

128×64 LED display module for Arduino supports many control chips. Fully compatible with Arduino, 51 Series, MSP430 Series, STM32 / 2, CSR IC, etc. Ultra-low power consumption: full screen lit 0.08W Super high brightness and contrast are adjustable With embedded driver/controller Interface type is IIC I2C/IIC Interface, need 2 IO only.

Available: Text Colour: Blue, Yellow, and Blue-Yellow 

Interface Definition

NOTE: SPI is Default Setting. How to change to  IC2 Below  Thanks to  Chas Haka for updating the Default setting.

1. This module supports IIC, 3-wire SPI and 4-wire SPI interface bus mode switching (see Datasheet How to change to IC2). The details are as follows.

Using 4.7K resistance to soldering only R3 and R4 resistors, choose a 4-wire SPI bus interface (default).
 B. Using 4.7K resistance to solder only R2 and R3 resistors, select a 3-wire SPI bus interface.
 Using 4.7K resistance to solder only R1R4R6R7, and R8 resistors, select the IIC bus interface.
2. After the interface bus mode is switched, you must select the corresponding software and wiring pins (as shown in Figure 1)

for the module to operate normally. The corresponding wiring pins are described as follows.
 A. 4-wire SPI bus interface. All pins need to be used.
 B. 3-wire SPI bus interface, only the DC pin does not need to be used(it can not be connected); other pins need to be used;
 C.select the IIC bus interface, only need to use the four pins GNDVCCD0D1, At the same time, the RES pin is connected to the high level (can be connected to the VCC), the DC and CS pins are connected to the power GND.
Specifications:
  • Driver IC: SSD1306
  • The default is a 4-wire SPI bus, which can choose a 3-wire SPI bus or an IIC bus
  • Size: 0.91 inch OLED
  • Resolution: 128 x 64
  • SPI / IIC interface
  • Size :27.0MM x 27.0MM x 4.1MM
  • Visual Angle: >160°
  • Input Voltage: 3.3V ~ 6V
  • Compatible I/O Level: 3.3V, 5V

Pin Description:

  • GND (Power ground)
  • VCC (Power + 3.3-5V)
  • D0 (SPI clock line for SPI interface and IIC clock line for IIC interface)
  • D1 (SPI data line for SPI interface and IIC data line for IIC interface)
  • RES (OLED reset, needs to be reset once after the Power-on)
  • DC (SPI data/command selection pin, used to set IIC address when IIC interface)
  • CS (OLED SPI chip select, active low; if you do not want to use must be grounded)

Package included: 1x 0.96 Inch Blue White Yellow-Blue SPI / IIC OLED LCD Module 7pin in your colour selection

Development  Resources: Demo codes, Schematics, Datasheets, etc

 

Skull     Hackaday serves up Fresh Hacks Every Day from around the Internet.

Robot
Instructables is a community for people who like to make things. Explore, share, and do your next project with us!

hub     Where the world builds software

mm Strawberry    Raspberry Pi Foundation: What would you like to make today?

infinity    Arduino’s mission is to enable anyone to enhance their lives through accessible electronics and digital technologies.

world
Wikipedia is a free online encyclopedia created and edited by volunteers worldwide and hosted by the Wikimedia Foundation.

 

Notes:

1. There may be slight size deviations due to manual measurement, different measuring methods and tools.
2. The picture may not reflect the actual colour of the item because of different photography lights, angles and display monitors.

Weight 0.030 kg
Dimensions 3 × 3 × 1 cm
Colour Text

Blue, White, Yellow / Blue, Yellow / Blue Non Soldered



Product Applications



Current Product Support

SKU Product Type Download/View
0.96 Inch LCD Blue White Yellow-Blue SPI / IIC OLED Module 7pin - Drawing Schematics Download
0.96 Inch LCD Blue White Yellow-Blue SPI / IIC OLED Module 7pin - Drawings Schematics Download

Q & A

There are no questions yet

Ask a question

Your question will be answered by a store representative or other customers.

Thank you for the question!

Your question has been received and will be answered soon. Please do not submit the same question again.

Error

Warning

An error occurred when saving your question. Please report it to the website administrator. Additional information:

Add an answer

Thank you for the answer!

Your answer has been received and will be published soon. Please do not submit the same answer again.

Error

Warning

An error occurred when saving your answer. Please report it to the website administrator. Additional information: