0.96 Inch White Blue Yellow-Blue SPI / IIC OLED LCD Module 6pin
Provides a rich sample program for STM32, C51, Arduino, Raspberry Pi and MSP430 platforms the OLED display, no need backlight, self-illumination, the display performance is better than the traditional LCD display, also lower consumption.
![0.96 Inch 6Pin IIC I2C SPI Interface OLED White LCD](https://temperosystems.com.au/wp-content/uploads/2022/05/0.96-Inch-6Pin-IIC-I2C-SPI-Interface-OLED-xxx-LCD-300x300.jpeg)
2 in stock
0.96 Inch Blue White Yellow-Blue SPI (default)/ IIC OLED LCD Module 6pin, no need for a backlight, self-illumination, and the display performance is better than the traditional LCD lower consumption.
128×64 LED display module for Arduino supports many control chips. Fully compatible with Arduino, 51 Series, MSP430 Series, STM32 / 2, CSR IC, etc. Ultra-low power consumption: full screen lit 0.08W Super high brightness and contrast are adjustable With embedded driver/controller Interface type is IIC I2C/IIC Interface, need 2 IO only.
Available: Text Colour Blue, Yellow, and Blue-YellowÂ
Interface Definition
NOTE: SPI is Default Setting. How to change to IC2 Below Thanks to Chas Haka for updating the Default setting.
- 1. This module supports IIC, 3-wire SPI and 4-wire SPI interface bus mode switching (see Datasheet ho to change to IC2). The details are as follows:
- A.Using 4.7K resistance to soldering only R3 and R4 resistors, choose a 4-wire SPI bus interface (default);
- B.Using 4.7K resistance to solder only R2 and R3 resistors, select 3-wire SPI bus interface;
- C.Using 4.7K resistance to solder only R1, R4, R6, R7, and R8 resistors, select the IIC bus interface;
- 2. After the interface bus mode is switched, you must select the corresponding software and wiring pins (as shown in Figure 1)
- for the module to operate normally. The corresponding wiring pins are described as follows:
-  A.select the 4-wire SPI bus interface, all pins need to be used;
-  B.select the 3-wire SPI bus interface, only the DC pin does not need to be used(it can not be connected), other pins need to be used;
-  C.select the IIC bus interface, only need to use the four pins GND, VCC, D0, D1, At the same time, the RES pin is connected to the high level (can be connected to the VCC), the DC and CS pins are connected to the power GND;
Features :
- Driver IC: SSD1306
- The default is a 4-wire SPI bus, which can choose a 3-wire SPI bus or an IIC bus
- Size: 0.96 inch OLED
- Resolution: 128 x 64
- SPI / IIC interface
- Size :27.0MM x 27.0MM x 4.1MM
- Visual Angle: >160°
- Input Voltage: 3.3V ~ 6V
- Compatible I/O Level: 3.3V, 5v
Pin Description:
- GND (Power ground)
- VCC (Power + 3.3-5V)
- SCL (SPI clock line for SPI interface and IIC clock line for IIC interface)
- SDA (SPI data line for SPI interface and IIC data line for IIC interface)
- RES (OLED reset, OLED needs to be reset once after the power-on)
- DC (SPI data/command selection pin, used to set IIC address when IIC interface)
Package included: 1x 0.96 Inch SPI / IIC OLED LCD Module 6pin
Development Resources: demo codes, schematics, datasheets, etc
   Hackaday serves up Fresh Hacks Every Day from around the Internet.
Instructables is a community for people who like to make things. Explore, share, and do your next project with us!
   Where the world builds software
  Raspberry Pi Foundation What would you like to make today?
  Arduino’s mission is to enable anyone to enhance their lives through accessible electronics and digital technologies.
Wikipedia is a free online encyclopedia created and edited by volunteers worldwide and hosted by the Wikimedia Foundation.
Notes:
1. There may be slight size deviations due to manual measurement, different measuring methods and tools.
2. The picture may not reflect the actual colour of the item because of different photographing lights, angles and display monitors.
Weight | 0.030 kg |
---|---|
Dimensions | 3 × 3 × 1 cm |
Colour Text | Blue, White, Yellow / Blue |
Product Applications
Current Product Support
SKU | Product | Type | Download/View |
---|---|---|---|
(TS-S014) (TS-S015) (TS-S016) | 0.96 Inch White Blue Yellow-Blue SPI / IIC OLED LCD Module 6pin - Drawing | Schematics | Download |
(TS-S014) (TS-S015) (TS-S016) | 0.96 Inch White Blue Yellow-Blue SPI / IIC OLED LCD Module 6pin - Drawings | Schematics | Download |